- Should drip edge be tight to fascia?
- Do I need drip edge on shed?
- How do you bend a drip edge?
- What color drip edge should I use?
- How far should shingles hang over the drip edge?
- What is the difference between drip edge and rake edge?
- Should rain gutters be installed under drip edge?
- What does a drip edge do on a roof?
- What goes first drip edge or felt?
- What kind of nails do you use for drip edge?
- Does drip edge go around entire roof?
- Can you install drip edge after roof?
- How much does drip edge cost?
Should drip edge be tight to fascia?
Nail thefurring strip to the fascia board near the fascia top – tight under any extending of roof decking (usually absent); the Drip edge will be installed 1/8″ proud of (away or out from) the furring strip in best practice or may be installed tight against the furring strip (reduces the life of the furring strip by ….
Do I need drip edge on shed?
Water will work its way back up under the edge of your shingles, however, with drip edge properly installed on your shed roof, this damaging water will be re-routed to drop vertically to the ground or gutter instead of permeating into your roof sheeting. … Here’s the right way to install drip edge on your shed roof.
How do you bend a drip edge?
How to do it:Place the metal in the brake finished side down, leaving about 2-1/2 inches out of the brake.Bend a 90 degree corner.Remove the metal, spin it end for end and flip it over so that the brown side is up. … Insert the shorted leg into the break about 1’4 inch to bend a slight kick into the flashing.More items…•
What color drip edge should I use?
If your home’s trim and fascia are white, it is recommended you select a white drip edge for seamless blending of elements throughout. If your home has more pops of brown, similar to the home displayed in the photo to the right, you may want to choose a brown drip edge.
How far should shingles hang over the drip edge?
¼ to ¾-inchAsphalt shingles should overhang the exterior edge of the drip edge by ¼ to ¾-inch. Check local building code for drip edge requirements prior to the start of your roofing project.
What is the difference between drip edge and rake edge?
Drip edge and rake edge are the first parts of the roof system to be installed. … They form a long, narrow piece of metal, which is installed along the perimeter your Roof Deck. Drip edge goes along your eaves trough areas and rake edge goes along your gable ends.
Should rain gutters be installed under drip edge?
Your gutter needs to be a few inches under the edge of your roof. … Drip edge gets installed under the first course of shingles and promotes water to run freely from roof edge down into gutter. Without it, water may run down behind your gutter, down fascia board and siding, leading to potential damage.
What does a drip edge do on a roof?
Drip edge is a metal flashing that is installed at the edges of the roof to help control the flow of water away from the fascia and to protect the underlying roofing components. Drip edge overhangs the sides of the roof and has a small metal flange that is bent away from the fascia.
What goes first drip edge or felt?
The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge. This lets any water that gets on the roof run down the underlayment and over the drip edge.
What kind of nails do you use for drip edge?
The drip edge is nailed in place using 1-1/2 galvanized roofing nails. A felt-tip marker works great for marking cuts. And, again, prying open the end with a small flat bar allows the pieces to overlap cleanly.
Does drip edge go around entire roof?
The correct placement of a roof drip edge is on top of the roof’s exterior cover directly between the sheathing and the fascia board, which forms a drainage gap between the drip edge and the fascia board. As a result, the drainage improves water flow and protects the roof from potential water damage.
Can you install drip edge after roof?
After your roof deck has been prepared, and before you install underlayment, you need to install drip edges at the eaves. You install drip edges on the rakes after you install the underlayment. … Step Two: Install drip edges on the eaves first. Place the drip edge down, aligning it so water will drip into the gutters.
How much does drip edge cost?
Drip Edges: $1-$2 per linear foot installed. Inspect and replace drip edges as necessary. Drip edges are added to the roof to direct water into the gutters. Other Damage – Have a professional inspect your eaves for damage before repairing fascia and soffits.